ConstructionCalculators

Acreage Calculator

Enter the sides of a lot, even an irregular one, or an area in any unit to get the acres, square feet, hectares and land value.

200 ft100 ft
Lot
ft
ft

You need

0.459acres

20,000 square feet

Square yards
2,222
Hectares1,858 m²
0.1858
Perimeterfor fencing
600 ft
Land value
$2,066

How Many Acres Is My Lot?

A 200 × 100 ft lot is 20,000 square feet, or 0.459 acres. Divide the area in square feet by 43,560, the number of square feet in one acre.

Common lot sizes in acres:

LotSquare feetAcres
50 × 100 ft5,0000.115
60 × 120 ft7,2000.165
100 × 100 ft10,0000.23
75 × 150 ft11,2500.258
100 × 200 ft20,0000.459
150 × 300 ft45,0001.033
330 × 660 ft217,8005

Real estate listings round these: a 75 × 150 ft lot is sold as about a quarter acre, and 150 × 300 ft as an acre. For anything you build, fence or plant, use the measured figure.

Square Feet in an Acre

One acre is exactly 43,560 square feet, or 4,840 square yards. Fractions of an acre come up most often with house lots:

1/8 acre
5,445 sq ft
1/4 acre
10,890 sq ft
1/3 acre
14,520 sq ft
1/2 acre
21,780 sq ft
3/4 acre
32,670 sq ft
1 acre
43,560 sq ft
2 acres
87,120 sq ft
Square feet, in square feet

As squares, a quarter acre is 104.36 ft on a side, a half acre 147.58 ft and a full acre 208.71 ft. A third of an acre, 14,520 square feet, fits on a lot about 100 × 145 ft.

How Big Is an Acre?

An acre is an area, not a shape. As a square it is 208.71 ft on each side, about 63.6 m. Historically it was a strip one chain wide and one furlong long, 66 × 660 ft: a chain is 66 ft and a furlong 10 chains, and an acre is still exactly 10 square chains. An American football field, end zones included, is 360 × 160 ft, or 1.32 acres, so an acre is about three quarters of one.

One acre two ways, next to a football field, at the same scale:

1 acre660 × 66 ft1 acre208.71 ft square1.32 acres360 × 160 ft
Drawn to the same scale. The strip is one chain by one furlong, the shape that defined the acre.

Between the goal lines the field is 300 × 160 ft, 1.1 acres, which is why "about a football field" is a fair picture of an acre.

How to Calculate Acreage

Multiply the length by the width in feet and divide by 43,560:

Acres = length (ft) × width (ft) ÷ 43,560200 ft × 100 ft = 20,000 sq ft20,000 ÷ 43,560 = 0.459 acres
  1. 1Take each side from the plat or survey, or measure it on the ground with a long tape or a measuring wheel. Measure level distances, not along the slope.
  2. 2For a rectangle, multiply length by width. For any other shape, split it into rectangles and triangles and add their areas.
  3. 3Divide the square feet by 43,560 for acres, or by 10,890 for quarter acres.
  4. 4In metric, divide square meters by 10,000 for hectares, or by 4,046.86 for acres.

The same 200 × 100 ft lot has a perimeter of 600 ft, which is the run of fence around it: turn that into posts, rails and panels.

From Frontage and Depth

Lot descriptions often give the frontage on the street and the depth: 150 ft of frontage and 300 ft of depth is 45,000 square feet, 1.033 acres. If the side lines are not parallel, average the front and back widths before you multiply, or use the Four Sides mode.

How to Find the Acreage of an Irregular Lot

Split the lot into triangles and add them up. For each triangle, Heron's formula gives the area from its three sides:

Area = √(s × (s − a) × (s − b) × (s − c)), where s = (a + b + c) ÷ 2Sides 200, 150 and 180 ft: s = 265√(265 × 65 × 115 × 85) = 12,976 sq ft12,976 ÷ 43,560 = 0.298 acres

Three sides close into a triangle only if the longest is shorter than the other two together; 100, 100 and 250 ft is not a lot but a typo, and the calculator says so instead of giving an area.

A four-sided lot needs one diagonal as well, from the front-left corner to the back-right. Four sides alone do not fix the shape: a 200 × 100 ft rectangle has a 223.6 ft diagonal and 20,000 square feet, but lean it into a parallelogram with a 260 ft diagonal and the same four sides enclose only 17,960 square feet.

The calculator's default four-sided lot, with the diagonal splitting it into two triangles:

200 ft100 ft180 ft110 ft230 ft
Front 200 ft, right 100 ft, back 180 ft, left 110 ft, diagonal 230 ft: 19,648 sq ft, 0.451 acres

Worked Example: a Five-Sided Lot

A lot with a front of 150 ft, a right side of 200 ft, a back of 120 ft, a short angled side of 90 ft and a left side of 160 ft needs two diagonals from the front-left corner, here 250 ft and 230 ft. They split it into three triangles:

  1. 1Front, right side and first diagonal (150, 200, 250 ft): 15,000 sq ft
  2. 2First diagonal, back and second diagonal (250, 120, 230 ft): 13,748 sq ft
  3. 3Second diagonal, angled side and left side (230, 90, 160 ft): 5,367 sq ft
  4. 4Total 34,114 sq ft ÷ 43,560 = 0.783 acres

Enter each triangle in the Triangle mode and add the results, or enter the first four-sided part in Four Sides and the last triangle separately.

  • More than five sides: keep drawing diagonals from the same corner, so the lot becomes a fan of triangles, and add them.
  • Curved boundaries: a creek or a cul-de-sac front can be stepped off as several short straight sides, or taken from the plat, which gives the arc length and radius.
  • Sloped land: acreage is measured on the level, in plan. Walking a hillside with a tape overstates it.

Acreage From a Map, Plat or Deed

The legal acreage of a parcel is in its deed and on the recorded plat or survey, and the property tax record usually repeats it. Those documents list each boundary line by its bearing and length, which you can enter side by side in the Four Sides or Triangle mode to check the stated figure.

Online maps and county parcel viewers let you click around a boundary and read the area. That is fine for planning a garden or a fence, but the lines on an aerial photo rarely sit exactly on the property corners, which are survey pins in the ground, not fences or tree lines. Only a licensed land surveyor can establish a boundary.

Old Deed Units

Older deeds measure in surveyor's chains, rods and links. Convert them to feet before you enter them:

UnitFeetArea unitSquare feet
Link0.66Square rod (perch)272.25
Rod, pole or perch16.5Square chain4,356
Chain66Acre43,560
Furlong660Square mile27,878,400

A chain is 100 links or 4 rods, and an acre is 160 square rods or 10 square chains, so a deed line of 12 chains 50 links is 825 ft.

Since January 1, 2023, federal standards define the foot for surveying as the international foot of exactly 0.3048 m. The old U.S. survey foot was 2 parts per million longer, so an acre measured in survey feet was about 4 parts per million larger: less than a quarter of a square foot on a one-acre lot.

Acreage From Corner Coordinates

If you have the corners as coordinates, from a GPS receiver, a survey or a map, the coordinate (shoelace) method gives the area directly. List the corners in order around the lot, in feet east (x) and north (y) of any point, then:

Area = ½ × |(x₁y₂ − x₂y₁) + (x₂y₃ − x₃y₂) + … + (xₙy₁ − x₁yₙ)|Corners (0, 0), (210, 0), (190, 120), (−10, 100) ft0 + (210 × 120 − 190 × 0) + (190 × 100 + 10 × 120) + 0 = 45,40045,400 ÷ 2 = 22,700 sq ft = 0.521 acres

A GPS-enabled phone is typically accurate to about 16 ft (4.9 m) under open sky and worse near buildings and trees, which matters on a house lot and hardly at all on a farm field. Use coordinates in feet or meters, not latitude and longitude in degrees.

From a Plat's Bearings and Distances

A plat describes each boundary line as a bearing and a distance, such as N 30° E, 100 ft. Turn each line into how far it runs east and north: east = distance × sin(bearing angle), north = distance × cos(bearing angle), with the signs set by the quadrant. N 30° E for 100 ft runs 50.0 ft east and 86.6 ft north. Add the lines up one by one to get each corner's coordinates, then use the formula above. Surveyors call this latitudes and departures.

Acres, Hectares and Square Miles

UnitEquals
1 acre43,560 sq ft = 4,840 sq yd = 4,046.86 m²
1 acre0.4047 hectares = 10 square chains = 160 square rods
1 hectare10,000 m² = 107,639 sq ft = 2.471 acres
1 square mile640 acres = 259 hectares = 1 section
1 township36 sections = 36 sq miles = 23,040 acres

A metric lot works the same way: the calculator's metric example, 60 × 30 m, is 1,800 m², which is 0.18 hectares or 0.445 acres.

Strips of land work the same way: a road right-of-way 66 ft wide, one chain, and one mile long is 66 × 5,280 = 348,480 sq ft, exactly 8 acres. A 20 ft utility easement along a 300 ft lot line takes 0.138 acres of it.

Switch the calculator to Metric to enter the sides in meters and read the answer in hectares, with acres beside it. A hectare is a square 100 m on a side, about two and a half acres. Sections and townships are the units of the Public Land Survey System: a quarter section is 160 acres, and a quarter of that, 40 acres.

Common Mistakes

  • Square yards for square feet. 20,000 square yards is 180,000 square feet, more than four acres. Check which unit a listing uses.
  • Four sides without a diagonal. Multiplying the average length by the average width works only for near-rectangles; a skewed lot comes out too big.
  • Measuring along a slope. A tape laid on a hillside reads long. Hold it level or take the distance from the plat.
  • Trusting the fence. Old fences often stray a few feet from the true line; the plat and the survey pins decide.
  • Rates per 1,000 sq ft. Seed, sod and fertilizer labels usually give rates per 1,000 square feet. An acre is 43.56 of those units, not 43.

What an Acre of Land Is Worth

U.S. farm real estate, land and buildings, averaged $4,500 an acre in 2026. Cropland ran about $6,020 an acre and pasture about $2,000, and state averages ranged from $735 to $23,600. Building lots near towns, with road frontage, water and sewer, sell for many times the farmland price.

Two parcels of the same size can differ several times in price: road access, utilities, zoning, flood zones, slope and soil all count, often more than the acreage itself.

The calculator starts at $4,500 an acre, so the 0.459-acre default lot comes to $2,066; in metric it starts at $11,120 a hectare, the same price per unit of land. For the ground itself, measure the part you will mow and work out the grass seed to cover it.

Frequently Asked Questions

How many square feet are in an acre?

43,560 square feet, which is also 4,840 square yards and 4,046.86 square meters. A quarter acre is 10,890 square feet and a half acre 21,780.

How big is an acre in feet?

An acre has no set shape. As a square it is 208.71 ft on each side; as the strip that defined it historically, one chain by one furlong, it is 66 × 660 ft.

How many acres is a 100 × 200 ft lot?

0.459 acres: 100 × 200 = 20,000 square feet, divided by 43,560.

How many acres is 10,000 square feet?

0.23 acres, a little under a quarter acre. A quarter acre is 10,890 square feet.

How do I find the acreage of an irregular lot?

Split it into triangles. Heron's formula gives a triangle's area from its three sides; for a four-sided lot, measure one diagonal as well, because four sides alone do not fix the shape. The calculator's Triangle and Four Sides modes do this for you.

How many acres are in a hectare?

2.471 acres. One acre is 0.4047 hectares, and a hectare is a square 100 meters on a side.

How many acres is a football field?

1.32 acres including the end zones (360 × 160 ft), or 1.1 acres between the goal lines. An acre is about three quarters of a football field.

How many acres are in a square mile?

640 acres. A section of land in the Public Land Survey System is one mile square, 640 acres, and a township is 36 sections.

How do I calculate acreage from linear feet?

Multiply the frontage by the depth, both in feet, and divide by 43,560: a lot 150 ft wide and 300 ft deep is 45,000 sq ft, 1.033 acres. The total length of the boundary alone does not give the area.

How much is an acre of land worth?

U.S. farm real estate averaged $4,500 an acre in 2026: about $6,020 for cropland and $2,000 for pasture, from $735 in the lowest state to $23,600 in the highest. Building lots near towns sell for much more per acre.

Sources

  • National Coordination Office for Space-Based Positioning, Navigation, and Timing. (n.d.). GPS accuracy.
  • National Football League. (2024). Official playing rules of the National Football League (Rule 1).
  • National Institute of Standards and Technology. (2026). Appendix C: General tables of units of measurement. In Specifications, tolerances, and other technical requirements for weighing and measuring devices (NIST Handbook 44).
  • National Institute of Standards and Technology & National Oceanic and Atmospheric Administration. (2020). Deprecation of the United States (U.S.) survey foot. Federal Register, 85, 62698.

Updated .

Cite this page as:

Daniel, P. Acreage Calculator. Available at: https://constructioncalculators.com/acreage-calculator/. Accessed: October 28, 2026.