How Much Muriatic Acid Do I Add?
Lowering total alkalinity from 150 to 100 ppm in a 20,000 gallon pool takes 256 fluid ounces of 31.45% muriatic acid: 8 quarts, or 2 gallons. To nudge pH down without a big alkalinity change, the label dose is a quart, 32 fl oz, a day for the same pool.
Fluid ounces of 31.45% acid to lower total alkalinity, and the daily dose for pH:
| Pool | −10 ppm | −50 ppm | pH a day |
|---|---|---|---|
| 5,000 gal | 12.8 fl oz | 64 fl oz | 8 fl oz |
| 10,000 gal | 25.6 fl oz | 128 fl oz | 16 fl oz |
| 15,000 gal | 38.4 fl oz | 192 fl oz | 24 fl oz |
| 20,000 gal | 51.2 fl oz | 256 fl oz | 32 fl oz |
| 25,000 gal | 64 fl oz | 320 fl oz | 40 fl oz |
| 30,000 gal | 76.8 fl oz | 384 fl oz | 48 fl oz |
| Pool | TA −10 ppm | TA −20 ppm | TA −50 ppm | pH, a day |
|---|---|---|---|---|
| 5,000 gal | 12.8 fl oz | 25.6 fl oz | 64 fl oz | 8 fl oz |
| 10,000 gal | 25.6 fl oz | 51.2 fl oz | 128 fl oz | 16 fl oz |
| 15,000 gal | 38.4 fl oz | 76.8 fl oz | 192 fl oz | 24 fl oz |
| 20,000 gal | 51.2 fl oz | 102.4 fl oz | 256 fl oz | 32 fl oz |
| 25,000 gal | 64 fl oz | 128 fl oz | 320 fl oz | 40 fl oz |
| 30,000 gal | 76.8 fl oz | 153.6 fl oz | 384 fl oz | 48 fl oz |
A quart is 32 fl oz and a gallon 128. Pool acid is sold mostly in gallon jugs, so the calculator rounds the purchase up to whole gallons.
Muriatic Acid by Pool Size
Acid to lower total alkalinity 20 ppm, next to HASA's daily pH dose, in fluid ounces:
Both grow in step with the gallons. Twice the water takes twice the acid for the same change, which is why a wrong pool volume throws off every dose.
How Much Muriatic Acid to Lower pH
HASA's label gives one dose for pH: one quart per 20,000 gallons of pool water per 24 hours, with the pump running, repeated a day later as needed to hold pH between 7.2 and 7.6. Test before each dose.
The label doesn't tie the dose to how high the pH is, because the same acid moves pH less in water with more alkalinity to buffer it. A quart in 20,000 gallons also lowers total alkalinity by about 6.3 ppm, so repeated pH doses slowly bring alkalinity down too. If pH keeps climbing back, check total alkalinity: HTH notes that high alkalinity keeps pushing pH up.
How to Calculate Muriatic Acid
Start from the acid itself. HASA's safety data sheet gives its specific gravity as 1.16, so a gallon weighs 9.68 lb, and at 31.45% 3.04 lb of it is hydrogen chloride. In 10,000 gallons, which weigh 83,450 lb, that lowers total alkalinity by about 50 ppm, or 10 ppm for each 25.6 fl oz:
Total alkalinity is measured as calcium carbonate, which is why the conversion runs through its equivalent weight: 36.46 lb of hydrogen chloride neutralizes the alkalinity of 50 lb of calcium carbonate. Half-strength acid takes more than twice as much, since it is also lighter; check the percent on the label, because the calculator assumes 31.45%.
How to Add Muriatic Acid to a Pool
Where and how HASA's directions say to pour it:
- 1Pump and filter running, during and an hour after
- 2Pour slowly at the deep end, at least 1 ft from the wall
- 3Spread it over as large an area as you can
- 1Test pH and total alkalinity, and work out the dose for your gallons.
- 2Put on goggles, rubber gloves and old clothes, as HASA's safety data sheet advises. Acid burns skin and eyes.
- 3With the pump running, pour the acid slowly at the deep end, at least a foot from the wall, over as large an area as possible.
- 4Keep the pump running for at least an hour. For pH, repeat after 24 hours if needed; for a big alkalinity drop, split the total into several doses and retest between them.
Never mix muriatic acid with chlorine or other chemicals in a bucket or jug; HASA's data sheet warns against it, and the mix gives off chlorine gas. If you need to shock as well, add the shock separately; work out the shock dose for your gallons.
How Often to Add Muriatic Acid
There is no fixed schedule: add acid when the test says so, when pH is above 7.6 or total alkalinity above 120 ppm. HTH's directions say to measure pH each time you add sanitizer, and HASA spaces pH doses 24 hours apart.
Store the jug upright in a clean, dry place out of reach of children and pets, as the data sheet directs, away from chlorine products. Rinse an empty jug thoroughly before throwing it out.
Muriatic Acid vs. Dry Acid
Dry acid is sodium bisulfate, a granular pH decreaser; HTH's pH Down is 92% of it. Its label dose is 16 oz per 10,000 gallons when pH is 8.0 to 8.4 and 24 oz above 8.4, broadcast over the deep end with the pump running and never pre-dissolved in a plastic bucket. By chemistry, lowering total alkalinity 10 ppm in 10,000 gallons takes about 2.2 lb of it, against 25.6 fl oz of muriatic acid.
Dry acid is easier to store and carry, but it leaves sulfate behind. Hayward discourages it for pools with salt cells in arid areas, where little fresh water dilutes the pool and by-products build up and can damage the cell.
Alkalinity and pH Targets
| Reading | Home pool target | Public-pool code (CDC) |
|---|---|---|
| Total alkalinity | 80–120 ppm (HTH, Pentair) | 60–180 ppm |
| pH | 7.2–7.6 (HASA, HTH); 7.2–7.8 (Pentair) | 7.0–7.8 |
If total alkalinity is low, raise it with baking soda instead; our pool alkalinity calculator works out both directions. Every dose depends on the gallons, so measure your pool's gallons if you only have a guess.
Frequently Asked Questions
How much muriatic acid do I add to lower alkalinity?
About 25.6 fluid ounces of 31.45% acid for each 10 ppm in 10,000 gallons, from the acid's strength and density on HASA's data sheet. In 20,000 gallons, dropping 50 ppm takes 256 ounces, 2 gallons.
How much muriatic acid to lower pH?
HASA's label: one quart per 20,000 gallons per 24 hours, with the pump running, repeated a day later if the pH is still above 7.6. That is 16 fl oz for 10,000 gallons and 48 fl oz for 30,000.
How much muriatic acid for a 10,000 gallon pool?
25.6 fl oz to lower total alkalinity 10 ppm, 51.2 fl oz for 20 ppm. For pH alone, the label dose is 16 fl oz, half a quart, a day.
How much muriatic acid is too much at once?
HASA's label caps the pH dose at one quart per 20,000 gallons in 24 hours and tells you to add less when in doubt. For a large alkalinity drop, split the total into doses and retest pH and alkalinity between them.
What should total alkalinity be?
HTH and Pentair target 80 to 120 ppm; the CDC public-pool code allows 60 to 180. pH should sit at 7.2 to 7.6 by HASA and HTH, 7.2 to 7.8 by Pentair.
Is muriatic acid the same as hydrochloric acid?
Yes. Pool muriatic acid is hydrochloric acid in water, 31.45% in HASA's product; the rest is water.
How much does a gallon of muriatic acid weigh?
About 9.68 lb. Its specific gravity is 1.16, so a gallon weighs 1.16 times as much as a gallon of water, and 3.04 lb of that is hydrogen chloride.
How long should the pump run after adding muriatic acid?
At least an hour. HASA's directions say the filter and pump must run while you add the acid and for at least one hour after.
Can I add muriatic acid and chlorine at the same time?
Never mix them: HASA's safety data sheet warns against mixing the acid with chlorine bleaches or other chemicals. Add each to the pool on its own, with the pump running, as HTH's directions put it.
How much does muriatic acid cost?
About $22.50 a gallon of 31.45% acid. The default job, lowering 20,000 gallons from 150 to 100 ppm, uses 2 gallons, $45.
Sources
- Centers for Disease Control and Prevention. (2023). Model aquatic health code (4th ed.).
- HASA. (n.d.). HASA muriatic acid: For swimming pools, lowers pH and alkalinity [Product sheet].
- HASA. (2026). Safety data sheet: HASA muriatic acid (SDS No. 110).
- Hayward. (2019). AquaRite owner's manual (092538 Rev. D).
- HTH Pool Care. (n.d.-a). Pool alkalinity up [Product label and directions].
- HTH Pool Care. (n.d.-b). Pool pH down [Product label and directions].
- Pentair. (2023). IntelliChlor salt chlorine generator installation and user's guide (P/N 520589 Rev. R).
Updated .
Cite this page as:
Daniel, P. Muriatic Acid Pool Calculator. Available at: https://constructioncalculators.com/muriatic-acid-pool-calculator/. Accessed: October 28, 2026.